What is the purpose of a keyway?
A keyway is a recess in a shaft or hub to receive a key, and these recesses are commonly cut on key-seating machines or by broaching, milling, planning, shaping, and slotting.
What does keyway mean?
1 : a groove or channel for a key . 2 : the aperture for the key in a lock having a flat metal key .
How is keyway made?
A key is usually made from steel and is inserted or mounted between the shaft and the hub of the component in an axial direction to prevent relative movement. Shaft and hub keyways are often cut on key seating machines but can also be made using broaching, milling, shaping, slotting EDM.
How deep are the keyways placed in the walls and slabs?
As shown on the detail most keyways are about 3 inches wide by 1.5 inches deep , the size of 2×4. The ideal way to install keyways is to place them centered on the reinforcements which can be difficult to install because you have to drill holes on the 2×4 to allow the dowls thru.
What is the purpose of a keyway in concrete?
A slot formed and poured on a footer or in a foundation wall when another wall will be installed at the slot location. This gives additional strength to the joint/meeting point.
What is a keyway on a lock?
“Keyway” is the term for the shape of the interface between a lock and its key. This is regardless of the shape of the key’s teeth – those bumps and ridges that resemble a mountain range if viewed from the side. The keyway is what prevents you from even beginning to push the wrong key into the wrong slot.
What is a Paracentric keyway?
paracentric . adj. 1. of or pertaining to a keyway with one or more wards on each side projecting beyond the vertical center line of the keyway to hinder picking 2. of or pertaining to a key blank made to enter such a keyway .
What does C keyway mean?
C keyway is Schlage’s most common key SC1 or SC4 depending on if it’s 5 or 6 pin.
What keyway does Kwikset use?
What keyway do you use ? – Yale US. We use a 5 pin KW1 ( Kwikset ) keyway as standard in our Yale® New Traditions™ and Yale® Design Elements™ product lines and a 6 pin KW ( Kwikset ) in our Yale® YH Collection™.
How does a keyway broach work?
Keyway broaches are used to form starter holes, remove material or shape a workpiece. These and other rotary broaches are used in a one-pass operation and have a bar-shaped design with several teeth that can progressively increase in height or shape from the starting end.
What is a keyway and how is it formed?
Keyway . A slot formed and poured on a footer or in a foundation wall when another wall will be installed at the slot location. This gives additional strength to the joint/meeting point. © Copyright 2016 Complete Design, Inc.
How do you remove a keyway?
Place the assembly over the key, and then thread the bolt into the shaft as far as it will go. Spin the nut downward against the block. Then use a wrench to apply enough force on a nut to remove the key from the shaft. If you apply enough downward movement, the key will be extracted.
What methods are used to determine the size of footings?
What methods are used to determine the size of footings ? The size of the footing is based on the value of soil bearing, footing location, and the load to be supported.
What is the purpose of the reinforcement in a slab on grade?
Reinforcement within a slab prevents cracks from opening and becoming wide and objectionable. These cracks may be due to drying shrinkage or due to externally applied loadings. When these cracks are kept tight, aggregate interlock will still exist and faulting will not occur.
What is the purpose of the footing?
Footings are an important part of foundation construction. They are typically made of concrete with rebar reinforcement that has been poured into an excavated trench. The purpose of footings is to support the foundation and prevent settling. Footings are especially important in areas with troublesome soils.